Ip tftp source-interface GigabitEthernet0 Ip nat inside source list 1 interface GigabitEthernet0/0/0 overload Vlan internal allocation policy ascending License udi pid ISR4331/K9 sn FDO2130203X No platform punt-keepalive disable-kernel-core Num-exp YOUR_DID_with_+_in_front YOUR_EXTENSIONĬreate cnf-files version-stamp 7960 11:59:31Īlias exec flash:/SCCP-Phones/ the changes/additions marked in bold: Tftp-server flash:/Ringtones/Ring1.raw alias Ring1.rawĭescription **Outgoing Calls to SIP Trunk** Tftp-server flash:/Ringtones/Analog2.raw alias Analog2.raw Tftp-server flash:/Ringtones/Analog1.raw alias Analog1.raw Tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.xml Tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml Tftp-server flash:/Ringtones/Pop.raw alias Pop.raw Ip nat inside source static 172.25.140.1 10.1.10.11 route-map SIP_NATĪccess-list 101 permit udp any any eq domainĪccess-list 101 permit udp any eq domain anyĪccess-list 140 permit ip host 172.35.140.15 anyĪccess-list 140 permit ip any host 172.35.140.15Īccess-list 140 permit ip host 172.25.140.1 anyĪccess-list 140 permit ip any host 172.25.140.1 Ip http timeout-policy idle 600 life 86400 requests 10000 Ip tftp source-interface GigabitEthernet0/0.25 Voice translation-profile -OutgoingĬrypto pki token default removal timeout 0 Request INVITE sip-header From modify "" "" No supplementary-service sip moved-temporarily Without further ado, here is the configuration: Did we mention that you need to send 11 digits? Google for a specific dial pattern for your situation. You could make this anything that you want provided it sends us 11 digits for North American calls. If you want something different (and we know you do), you must contrive the dial pattern on your own. Again, we must receive 11 digits for a North American call to work. Yes, that means you! We expect you to dial 11 digits. We are expecting you to dial 1NXXNXXXXXX within 10 seconds. The outbound pattern is set to ".T" which quite literally means "Dial at least one digit and then wait for timeout. However, note that we will always the deliver the call in the +1NXXNXXXXXX format. So if you want a hunt-group or dial-peer, you are on your own to figure out that configuration (Dr. There is no way we can predict what you want to do with your internal routing. Inbound calling is done via the "num-exp" argument for a single DID and a single extension. ***This configuration is designed around a very specific (but according to our help desk, common) network configuration.Ģ. Locate you trunk and click "Modify Trunk" **You MUST set your trunk to IP Authentication. The SIP Port, should be locked down to and IP Addresses and also forwarded to your CME. *The RTP Ports MUST be forwarded and accepted from ANY IP ADDRESS by your firewall. To that end, the firewall was also configured to Statically Source NAT port 5060 for all traffic received from the CME's IP Address on port 5060. Additionally, this configuration assumes IP Authentication which, with, requires a specific port for SIP traffic. The firewall was configured so that UDP ports 5060 (SIP) and 16384 - 32767 (RTP) are forwarded to the private IP address of the CME. This configuration assumes you want to have your CME on a router that faces your LAN and is behind a firewall. The following config was built using CME 10 on a Cisco Router running IOS v 15.1. Please consult this documentation for step-by-step instructions: **** **** NOTE TO CUBE USERS: You MUST force EARLY OFFER for media to work.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |